TD1410 PDF

Techcode TD datasheet, 2A KHZ 20V PWM Buck DC/DC Converter (1- page), TD datasheet, TD pdf, TD datasheet pdf, TD pinouts. Find great deals for 5pcs Power PWM Controller TD Sop8. Shop with confidence on eBay!. Altech TD Terminals are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Altech TD Terminals.

Author: Kazranos Moogujin
Country: Mayotte
Language: English (Spanish)
Genre: Software
Published (Last): 4 March 2004
Pages: 440
PDF File Size: 17.20 Mb
ePub File Size: 10.75 Mb
ISBN: 206-2-59787-136-4
Downloads: 32718
Price: Free* [*Free Regsitration Required]
Uploader: Zugor

Bypass Vin to GND with a suitably large capacitorto eliminate noise on the input. SW is the switch node that supplies power to the output.

EN Allows the switching regulator circuit to be shutdown using logic level signals thus dropping the total input supply current to approximately 30uA. Allows the switching regulator circuit to be shutdown using logic level signals thus dropping the total input supply current to approximately 30uA. Once exception to this is the output switch pin, which should not have large areas of copper. For the inductor, depending on the physical size, type of core material and the DC resistance, it could either act as a heat sink taking heat away from the board, or it could add heat to the board.

This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation is not implied. Higher ambient temperatures require more heat sinking. An enable function, an over current protection function and a short circuit protection function are built inside. Stresses greater than those listed under Maximum Ratings may cause permanent damage to the device.

For best results, external components should be located as close to the switcher IC as possible using ground plane construction or single point grounding. Furthermore, some of these components such as the catch diode will add heat to the PC board and the heat can vary as the input voltage changes. Vendor Web Site 1 Diodes,Inc. The data for these curves was taken with the TD SOP8 package operating as a buck-switching regulator in an ambient temperature of 25oC still air.

  PLANSUL LUI NIETZSCHE PDF

The SOP8 package needs a heat sink under most conditions. The size of the heat sink depends on the input voltage, the output voltage, the load current and the ambient temperature.

For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper should be used in the board layout.

Access Denied

FB Senses the regulated rd1410 voltage to complete the feedback loop. A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching currents needed by the regulator GND Circuit ground.

Other factors are, trace width, total printed circuit copper area, copper thickness, single or double-sided, multi-layer board and the amount of solder on the board.

TD operates from a 3. Power Switch Output Pin. An internal compensation block is built in to minimize external component count. The device includes a voltage reference, oscillation circuit, error amplifier, internal PMOS and etc. Icc vs Temperature Figure 8. Care must be taken in layout. This pin should be placed outside of the Schottky Diode to output capacitor ground path to prevent switching current spikes from inducing voltage noise into TD Drive EN pin high to turn on the t1410, drive it low to turn it off.

Physically locate both resistors near the IC, and route tx1410 wiring away form the inductor especially an open core type of inductor.

The TD junction temperature rises above ambient temperature for a 2A load and different input and output voltages. If open core inductors are used, special care must be taken as to the location and positioning of this type of inductor. Gd1410 to absolute maximum rating conditions for extended periods may affect reliability. EN is a digital input that turns the regulator on or off. To minimize coupling to sensitive circuitry, the PC board copper area connected to this pin should be kept a minimum.

Wiring inductance, stray capacitance, as well as the scope probe used to evaluate these transients, all contribute to the amplitude of these spikes.

As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring inductance can generate voltage transients which can cause problems. The voltage spikes are present because of the fast switching action of the output switch, and the parasitic inductance of the output filter capacitor, To minimize these voltage spikes, special low inductance capacitors can be used, and their lead lengths must td1401 kept short.

  CVSA OUT OF SERVICE CRITERIA PDF

Datasheet 2A KHZ 20V PWM Buck DC/DC

The feedback threshold voltage is 1. Parameters Symbol Test Condition Min. This is the positive input supply for the IC switching regulator. The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching currents needed by the regulator. An additional small LC filter can be added to the output as shown in Figure 14 to further reduce the amount of output ripple and transients.

These temperature rise numbers are all approximate and there are many factors that can affect these temperatures. When using the adjustable version, special care must be taken as to the location of the feedback resistors td1140 the associated wiring. The effectiveness of the PC board to dissipate heat also depends on the size, quantity and spacing of other components on the board, as well as whether the surrounding air is still or moving.

Through an external resistor divider network, FB senses the output voltage and regulates it. Typical Application Circuit 3. It achieves 2A continuous output current over a wide input supply range with excellent load and line regulation. Some of these factors include board size, shape, thickness, position, location, and even board temperature. Supply Voltage Input Yd1410. Large areas of copper provide the best transfer of heat lower thermal resistance to the surrounding air, and moving air lowers the thermal resistance even further.

Package thermal resistance and junction temperature rise numbers are all approximate, and there are many factors that will affect these numbers. Switching Frequency vs Temperature Figure 6.