ASTM E1876 PDF

Buy ASTM E Standard Test Method for Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio by Impulse Excitation of Vibration from SAI. Status: Withdrawn ยท Replaced by: ASTM E Metals — Mechanical Testing; Elevated and Low-Temperature Tests; Metallography(ASTM VOL ). Purchase your copy of ASTM E – 15 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available.

Author: Shanos Sacage
Country: Guinea
Language: English (Spanish)
Genre: Love
Published (Last): 11 November 2004
Pages: 284
PDF File Size: 5.80 Mb
ePub File Size: 3.42 Mb
ISBN: 863-6-61444-133-2
Downloads: 6203
Price: Free* [*Free Regsitration Required]
Uploader: Bracage

There is no requirement for complex support systems that require elaborate setup or alignment.

The dynamic shear modulus, or modulus of rigidity, is found using torsional resonant vibrations. The testing zstm these materials shall be done in compliance with these material specific standards.

The testing of these materials shall be done in compliance with these material e8176 standards. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen.

The dynamic shear modulus, or modulus of rigidity, is found using torsional resonant vibrations.

ASTM E1876 – 15

Different resonant frequencies can be excited dependent on the position of the support wires, the mechanical impulse and the microphone. Flat plates may also be measured similarly, but the required equations for determining the moduli are not presented.

Link to Active This link will always route to the current Active version of the standard. Where possible, the procedures, sample specifications and calculations are consistent with these test methods. Flat plates may also be measured similarly, but the required equations for determining the moduli are not presented. Dynamic Young’s modulus is determined using the resonant frequency in either the flexural or longitudinal mode of vibration. Specimen descriptions should include any specific thermal treatments or environmental exposures that the specimens have received.

  WEB DIZAJN KNJIGA PDF

Theory | IMCE – Your partner in the Impulse Excitation Technique

Test Methods CCCCC asm, and C may differ from this test method in several areas for example; sample size, dimensional e11876, sample preparation. Dedicated software will determine the resonant frequency with high accuracy to calculate the elastic properties based on the classical beam theory.

Dynamic Aastm modulus and dynamic shear modulus are used to compute Poisson’s ratio. To determine the shear modulus, the equipment measures the torsional vibration frequency see picture and calculates the shear modulus using the mass and dimensions of the sample according to the different standards ASTM E, ISOEN Any specimen with a frequency response falling outside the prescribed frequency range is rejected. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen.

A range of acceptable resonant frequencies is determined for a specimen with a particular geometry and mass. It is the responsibility of the user of this asttm to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Material damping or internal friction is characterized by the decay of the vibration amplitude of the sample in free vibration as the logarithmic decrement. Test Methods CCCCCand C may differ from this test method in several areas for example; sample size, dimensional tolerances, sample preparation.

To determine the Young’s modulus, the equipment measures the flexural vibration frequency see picture and calculates the Young’s modulus using the mass and dimensions of the sample according to the different standards ASTM E, ISOEN Dynamic Young’s modulus is determined using the resonant frequency in either the flexural or longitudinal asm of vibration. There is no requirement for complex support systems that require elaborate setup or alignment.

  PROBABILIDAD Y ESTADISTICA PARA INGENIERIA Y CIENCIAS PDF

The dynamic shear modulus, or modulus of rigidity, is found using torsional resonant vibrations. The actual dynamic elastic modulus of each specimen need r1876 be determined as long as the limits of the selected frequency range are known to include the resonant frequency that the specimen must possess if its geometry and mass are within specified tolerances.

Afterwards, the acquired vibration signal in the time domain is converted to the frequency e876 by a fast Fourier transformation.

No other units of measurement are included in this standard. Where possible, the procedures, sample specifications and calculations are ast with these test methods. Where possible, the procedures, sample specifications and calculations are consistent with these test methods.

For predefined shapes like rectangular bars, discs, rods and grinding wheels, the dedicated software calculates the sample’s elastic properties using the sample dimensions, weight and resonant frequency ASTM E Link to Active This link will always route to the current Active version of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.