ASTM B265 PDF

ASTM Gradel, JIS Grade, TIA, RMI 25, TIMETAL 35A, ST Sheet and plate. ASTM B Gr1, Mil-T CP Bars and billets. ASTM B Gr1. Tube. ASTM B Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality Titanium Plates, Sheets & Coils, Titanium sheets & plates.

Author: Moogutaxe Tygolkree
Country: Barbados
Language: English (Spanish)
Genre: Sex
Published (Last): 11 October 2005
Pages: 279
PDF File Size: 5.15 Mb
ePub File Size: 7.80 Mb
ISBN: 802-6-13766-365-9
Downloads: 44723
Price: Free* [*Free Regsitration Required]
Uploader: Akinokasa

Final product hydrogen shall be reported.

Titanium Plates, Sheets & Coils

Ingot hydrogen need not be reported. The g265 of titanium is determined by difference. Permission rights to photocopy the standard may also be secured from the ASTM website www.

This specification covers annealed titanium and titanium alloy strip, sheet, and plate.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. In cutting samples for analysis, the operation should be carried out insofar as possible in a dust-free atmosphere because utmost care must be used bb265 sampling titanium for chemical analysis due to its great affinity for elements such as oxygen, nitrogen, and hydrogen.

Alternate techniques are discussed in Guide E Heat numbers shall occur at least 3 times across the width of the sheet and at intervals not greater than 2 ft 0. This abstract is a brief summary asfm the referenced standard.

Product analysis limits shall be as specied in Table 3. Referee Test and Analysis The report shall include results of all chemical analysis, tensile tests, and all other tests required by the specication. Current edition aatm May 1, Approved May 1, The characters shall be not less than 38 in.

Tensile properties shall be determined asrm a strain rate of 0. The bend shall be made on a radius equal to that shown in Table 1 for the applicable grade. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

  ECE R43 PDF

Lower hydrogen may be obtained by negotiation with the manufacturer. Silicon each total 0. Work Item s – proposed revisions of this standard. Annealed material may be furnished aatm descaled, as sandblasted, or as ground, or both sandblasted and ground.

There is no under tolerance in weight for titanium sheets, under tolerance being restricted by the permissible thickness variations.

The utmost care must be used in sampling titanium for chemical analysis because of its great affinity for elements such as oxygen, nitrogen, and hydrogen. Specied thickness was corrected from 0. In titanium these elements typically include aluminum, vanadium, tin, chromium, molybdenum, niobium, zirconium, hafnium, bismuth, ruthenium, palladium, yttrium, copper, silicon, cobalt, tantalum, nickel, boron, manganese, and tungsten.

Unalloyed titanium plus 0. Two bends shall be made in the L direction and two in the T direction. Methods of Chemical Analysis MPa Product analysis tolerances cover variations between laboratories in the measurement of chemical content of the specimen. This is in accordance with the round-off method of Practice E If the results of the retest conform to the specication, then the retest values will become the test values for certication.

Only original conforming test results or the conforming retest results shall be reported to the purchaser. A superscript epsilon indicates an editorial change since the last revision or reapproval. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Therefore, properties for aged material shall be negotiated between manufacturer and purchaser.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  CANCION DE CUNA LEO BROUWER PDF

ASTM B _图文_百度文库

For plates up to 10 in. If the results for the retest fail to conform to the specication, the material will be rejected in accordance with Section The characters shall be sufficiently stable to withstand ordinary handling. When the straight edge is placed on a single high point, the maximum deviation from the plate at each end shall be no greater than 0.

Grade 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. E For Grades 5, 6 and 32 the elongation on materials under 0. For sheet and strip, the bend test specimen shall stand being bent cold through without fracture in the outside of the bent portion.

If shipped as descaled, sandblasted, or ground, the manufacturer shall be permitted to remove minor surface imperfections by spot grinding if such grinding does not reduce the thickness of the material below the minimum permitted by the tolerance for the thickness ordered. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

TITANIUM ALLOYS TECHNICAL DATA

NOTE 2—If the longer dimension is under 36 in. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any ashm mentioned in this standard.

Therefore, product analysis for elements not listed in Table 2 shall not be required unless specied and shall be considered to be in excess of the intent of this specication. D Axtm elements need not be reported unless the concentration level is greater than 0.