Aiphone GH-1KD Audio/Video Tenant Station – Overview: The GH-1KD is used to view and communicate with a person at a GH entrance panel. The unit. Distribution point 1Px2 GH-1KD 1Px2 Power supply Door bell B  Distribution terminal (junction): sold separately, not available from Aiphone. c. Find great deals for Aiphone Gh-1kd Audio/video Tenant Station. Shop with confidence on eBay!.
|Country:||Saint Kitts and Nevis|
|Published (Last):||12 May 2015|
|PDF File Size:||14.10 Mb|
|ePub File Size:||16.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
Set up the modules. Common trunk line 1, 2 2. How to reset password?
Table of Contents Add to my manuals Add. Although the entrance station is weather resistant, it is recommended that it not be directly exposed to weather conditions. In such cases, retry the programming again from the beginning. Put back the terminal cover. I have tried removing the batteries, but it still persists. Home Security Answered on Dec 13, Optional activation of outside light while talking to entrance station Optional connection of panic call station GFK- PSalerting with tone and call to Concierge Entrance monitoring Separate volume controls for call tone and communication Optional handset for privacy GH-HS Simple 2 separate pair common bus wiring 2 conductor for audio, 2 conductor for video Surface mounts to wall on 1-gang box or ring ABS plastic construction GH-1KD Spec Sheet Pg.
After all wiring is completed and the residential station has been replaced, turn off the power to GH-BC temporarily and then turn it back on. If the programming was unsuccessful, an alarm beep will be emitted. Most likely u may have to change the power supply s. Posted on Aug 24, Be the first to answer.
Aiphone Gh-1kd Audio/video Tenant Station
Hands-free audio communication Door release to the door where communication is. Surface-mount box GFB c. This manual also for: Home Security Answered 20 hours ago. Make sure that all units are installed and wired properly. PSalerting with tone and call to Concierge Entrance monitoring.
Make sure that all units are installed and wired properly. If you have volts on one side, but no voltage on the other, gh-1kkd is bad and should be replaced. Rain hood GF-H b. Bus control unit c. While using the mounting gauge to make adjustments, tighten the screws. Lawrence Oravetz Level aaiphone Expert Answers.
You can change the “Welcome” text. A continuous beep will be emitted to verify the communication link has been cleared.
Aiphone Gh-1kd Audio/video Tenant Station | eBay
To cancel the communication link, display the assigned name and press the call button for at least 3 seconds. This warranty covers bench repairs only,and any repairs must be made at the shop or place designated in writing by Aiphone. Page of aiphoone Go. Page 14 Failure to do so could result in pinching that may damage the wiring. Recent Popular Answered Unanswered.
An electronic beep will be emitted twice. Sub trunk line 1 – 4 Sub trunk line 2 – 4 are the same as 1. An electronic beep will be emitted once. Surface mounts to wall on 1-gang box or ring. Connect the wiring to the terminal block. An electronic sound will be emitted three times for a third residential station and four times for a fourth residential station. For GH-NS, display the room you want to correct and reprogram all the residential stations in the single apartment following steps 4 and following.
If power supply is interrupted during programming, the programmed information might be lost. Homerun gn-1kd For details, see Do not gn-1kd station-to-station wiring and homerun wiring. Common trunk line 1, 2 2. For information on how to use the setup tool, see the text. Ask a Question Usually answered in minutes! Are you an Aiphone Home Security Expert?
Home Security Answered 2 days ago. Plug in the ribbon cables between modules in a daisy-chained manner. Mount each module panel to the front frame.
The call is answered by one touch of the Talk. Skipped at time of entrance station monitoring. Marvin Level 3 Expert Answers. Residential station For details, see From the speech module to the next module, insert the aiiphone connector into the socket.
Move the lever to the desired position. Do not press the button longer than 1 second An electronic beep will be emitted once. What would cause this?